Search results for 'ace'

Full sized vertical grip
Contoured finger swells allow a firm grip even with gloved hands
Secure watertight storage compartment
Customizable foam storage block with quick access tab diminishes rattle
Flat non-slip bottom surface aids in supported firing positions

The Strike Industries M-LOK Cable Management Covers add a positive tactile feeling but also utilizes the patent pending SI Cable Management System® (CMS) function enables you to organize and store excess wire from your weapon light or any other cabled accessories. Instead of tucking wire anywhere you can and using cable ties or tape to hold it down, the SI CMS will offer you a place to route and/or contain loose wire inside the cover cavity. Cables can be routed alongside the handguard, across to the other side, 90-degrees or U-shape. The directions and possibilities are almost endless. Designed to be low-profile (6.20mm (0.24”) height) and used in any orientation, the contoured covers add ergonomic textured surfaces to your handguard. Made of durable and lightweight polymer, the covers are also a quick and affordable upgrade to mitigate any heat transfer between the barrel and the shooters hands while organizing and routing cables just about any way you want. Available in a Long version that is 79.80mm (3.14”) in length that comes in a 2-pack or a Short version that is 39.90mm (1.57”) in length that comes in a 4-pack. Get one length or both and always have the Strike Industries M-LOK Cable Management Covers you need to get a grip and manage your cables at the same time.

COMPATIBILITY: M-LOK

NOTE: LINK screws and nuts provided are not manufacturer by Strike Industries. Please make routine checks that the screws and nuts are secure as part of the preventive maintenance of the firearm.

Torque: Do not exceed 20 in/lbs (2.26 nM) for the LINK screws

NTOA Approved
The Dura Grip series vertical grip. Our Dura Grip line of vertical grips are all CNC machined aluminum and designed to last. For those that seek a bit more from their accessories the metal design is built to take some serious punishment right down to the steel mounting screw. The Handy version is our bare bones version for those of you that need the extra bells and whistles. Not everyone runs optics or flashlights and we had you in mind when designing our Handy version. Dura Grip Handy version gives you unsurpassed ergonomics with increased surface area with lighter weight. Our Dura Grip line also are convertible from full size to CQB configurations in just seconds. The Dura Grip Handy is water-resistant (not water-proof) Have other battery dependent accessories? Our Dura Grip line accommodate up to 3 123A batteries. The bottom cap has soft lining in order to keep batteries safe and protected.

Strike Industries LINK attachment system takes the age old question Key-Mod vs. M-Lok and came up with the ultimate solution, a dual interface design compatible with both M-Lok and Key-Mod, same hardware with no need for additional parts. This Aluminum rail section allows the attachment of various M1913 Picatinny spec rail-mounted accessories such as vertical grips, lights, lasers,  etc. The Dual interface rail section also features beveled ends to reduce snagging and eliminate sharp corners and edges.  

The Strike Ambush 45-Degree Optic Mount gives you a modular dual mounting plate design which covers just about all mainstream red dots on the market. When you want to run a dual optic setup and have a close distance Mini/Micro Red Dot Sight (MRDS) with a Low Power Variable Optic (LPVO) scope, this 45-degree optic mount is a low-profile and high-strength accessory without forcing you to pick only one red dot you have to pair it up with. The 45-degree angle should get you out of the way of most LPVO scopes along with two mounting positions to pick from on the SI Multi-Optic Mount side. Easily place a MRDS alongside a LPVO with the low-profile SI-Ambush Picatinny rail mount that either sits flush with the top of the Pic rail or slightly below making it easier to sit under a scope or scope mount. The Strike Ambush 45 comes with a dual footprint mounting plate which has the SI Multi-Optic Mount on one side and the Aimpoint® Micro Standard footprint for T-1/T-2 compatible red dots on the other side making this a new innovative modular option for a diverse market. The SUS630 hardened stainless steel Picatinny rail mount is ambidextrous for either side. The 6061-T6 aluminum mounting plate can be flipped to select which MRDS but also oriented to work with the right or left side of the Pic rail. Fitment for one or fitment for almost all MRDS’ on the market, the Strike Ambush 45-Degree Optic Mount gives you a simple, compact and modular just about all-in-one solution.

MOUNT COMPATIBILITY: 1913 Picatinny

(See individually listed red dot compatibility and suggested hardware to use in PRODUCT SPEC tab)
RED DOT COMPATIBILITY:
-Aimpoint Micro Standard
-C-MORE, DELTAPOINT PRO, DOCTER/NOBLEX, & RMR STANDARDS
-SHIELD STANDARD: SHIELD FOOTPRINT USING ONLY HOUSING REAR POSTS
*NOTE: Some specific red dots require screws provided by user listed in PRODUCT SPEC tab
NOT COMPATIBLE:
-SIG SAUER ROMEO1, ROMEO1PRO

WARNING:
-When using screws provided in the package, there is always a chance of hardware marring your optic housing finish/coating
-Be careful and use your best judgment on which hardware to use for your specific setup
-All installations should only be done by a certified professional gunsmith and properly tested to pass all safe and function tests

Torque: Do not exceed 15 in/lbs (1.69 nM) for the Picatinny mount screw