Search results for 'Free Floating Handguard'

The LINK Anchor Handstop is made from a heat resistant polymer that allows comfortable grip in any shooting condition. It has a low profile design that allows mounting through any MLOK or KeyMod openings. The unique tooth design allows the handstop to be reversible, giving the option for either a "push" or "pull" style grip. With the added ridges on the surface, the LINK Anchor provides unmatched dexterity from your palm to the fingertips. A true lightweight modification that is not only comfortable , has an aggressive look, and will improve accuracy over time by a stabilizing your grip. Learn More

The Strike Industries Angled Vertical Grip with Cable Management (M-LOK) is engineered like no other grip on the market. The grip angle sits on the handguard at 86 degrees. Patent pending SI cable management function enables you to organize and store excess wire from your weapon light or any other cabled accessories in multiple configurations. Instead of tucking wire anywhere you can and using cable ties or tape to hold it down, the cable management feature will offer you a place to route and/or contain loose wire inside the grip cavity. The side cuts at the top middle of the grip allow for easier pressure switch attachment. Compared to the Short version, the Long version has an added built-in stability feature when you place the L-shaped bottom onto a table edge/corner or as a barricade stop, giving you another way to get back on target faster downrange. The Short version can be mounted in either direction for your own preferred and personal setup and is low-profile form helps to minimize snags. The forward angle provides more of a natural wrist angle and increased rigidity of forearm. Designed with textured palm and finger areas with flat sides for positive handling and easier manipulation of the firearm. Made from durable and lightweight polymer compatible with M-LOK rails, the Strike Industries Angled Vertical Grip with Cable Management (Long) gives the shooter control while handling or firing the weapon, added stability (Long) with table/edge corner or as a barricade stop and an innovative way to ensure total cable management. No messy wires.

COMPATIBILITY: M-LOK

DISCLAIMER:
-Always check with your state and local laws. We are not lawyers.
-LINK screws and nuts provided are not manufacturer by Strike Industries. Please make routine checks that the screws and nuts are secure as part of the preventive maintenance of the firearm.

Torque: Do not exceed 20 in/lbs (2.26 nM) for the LINK screws

Learn More

The Strike Gear® Cable Management System® Sleeve offers a way for you to attach your switch or pressure pad and secure wires alongside the handguard of your weapon. Just like the rest of the SI Cable Management System® (CMS) line of products, keep your gear organized and personalized for each user. The SI CMS Sleeve is made of two polyester (x2) elastic webbing loops, the main loop sized 145mm (5.71”) in diameter to stretch over your handguard and smaller loop sized 8mm (0.32”) height x 21mm (083”) base width for a switch/pressure pad. If you do not have a mount or desire your switch/pressure pad to be in a specific place, the CMS Sleeve has a small elastic loop for you to secure and place almost exactly where you want it. The small loop has been sized to fit majority of the switches/pressure pads on the market. The main loop is sized to fit SI handguards and just about any handguard on the market. Both the main and small loop allow you to organize, tuck or run loose wire. No messy wires. Add a little protection against sharp rail slot edges. The Strike Gear® Cable Management System® Sleeve gives a customized way to attach a switch or pressure pad and manage your cables in a cost-effective way. Developed to continue the line of Strike Gear® soft goods accessories to help you organize.

COMPATIBILITY:
-Main loop: 145mm (5.71") in diameter with a ±3.0-5.0mm (±0.12-0.20") stretch
-Small loop: 8mm (0.32”) height x 21mm (083”) base width with a ±3.0-5.0mm (±0.12-0.20") stretch

WARNING AND DISCLAIMER: TO PREVENT HARM OR INJURY, THIS FABRIC MAY MELT IF HANDGUARD/RAIL AND/OR WEAPON IS OVERHEATED. USE WITH CAUTION.

Learn More

Strike Industries LINK attachment system takes the age old question Key-Mod vs. M-Lok and came up with the ultimate solution, a dual interface design compatible with both M-Lok and Key-Mod, same hardware with no need for additional parts. This Aluminum rail section allows the attachment of various M1913 Picatinny spec rail-mounted accessories such as vertical grips, lights, lasers,  etc. The Dual interface rail section also features beveled ends to reduce snagging and eliminate sharp corners and edges.  

Learn More

The Strike Industries Magwell for CZ Scorpion EVO is a flared design specifically for Scorpion EVO pistols and carbines to provide easier magazine insertion for fast reliable reloading while adding SI styling. The benefit of adding a funnel-like magwell to help prevent the dreaded reload bobble outweighs the added material of this lightweight SI Magwell. With the addition of an increased radial edge in front of receiver, this magwell aids in improving grip support for the offhand. This magwell is made of high-strength impact resistant custom blended SI Polymer Extreme material. Add consistency and cut fractions of seconds off your reloads now with the Strike Industries Magwell for CZ Scorpion EVO. A perfect pairing with the SI Mag Release For CZ Scorpion EVO.

COMPATIBILITY: All CZ Scorpion EVO models (except 3+)
NOT COMPATIBLE: CZ Scorpion EVO 3+

WARNING: DO NOT OVERTIGHTEN set screw when installing. Tighten only until end of set screw is flush with the nut. Failure to properly install will result in magazine not dropping freely.

Learn More