製品

The Strike Industries M-LOK Cable Management Covers add a positive tactile feeling but also utilizes the patent pending SI Cable Management System® (CMS) function enables you to organize and store excess wire from your weapon light or any other cabled accessories. Instead of tucking wire anywhere you can and using cable ties or tape to hold it down, the SI CMS will offer you a place to route and/or contain loose wire inside the cover cavity. Cables can be routed alongside the handguard, across to the other side, 90-degrees or U-shape. The directions and possibilities are almost endless. Designed to be low-profile (6.20mm (0.24”) height) and used in any orientation, the contoured covers add ergonomic textured surfaces to your handguard. Made of durable and lightweight polymer, the covers are also a quick and affordable upgrade to mitigate any heat transfer between the barrel and the shooters hands while organizing and routing cables just about any way you want. Available in a Long version that is 79.80mm (3.14”) in length that comes in a 2-pack or a Short version that is 39.90mm (1.57”) in length that comes in a 4-pack. Get one length or both and always have the Strike Industries M-LOK Cable Management Covers you need to get a grip and manage your cables at the same time.

COMPATIBILITY: M-LOK

NOTE: LINK screws and nuts provided are not manufacturer by Strike Industries. Please make routine checks that the screws and nuts are secure as part of the preventive maintenance of the firearm.

Torque: Do not exceed 20 in/lbs (2.26 nM) for the LINK screws

The Strike Industries Magwell for CZ Scorpion EVO is a flared design specifically for Scorpion EVO pistols and carbines to provide easier magazine insertion for fast reliable reloading while adding SI styling. The benefit of adding a funnel-like magwell to help prevent the dreaded reload bobble outweighs the added material of this lightweight SI Magwell. With the addition of an increased radial edge in front of receiver, this magwell aids in improving grip support for the offhand. This magwell is made of high-strength impact resistant custom blended SI Polymer Extreme material. Add consistency and cut fractions of seconds off your reloads now with the Strike Industries Magwell for CZ Scorpion EVO. A perfect pairing with the SI Mag Release For CZ Scorpion EVO.

COMPATIBILITY: All CZ Scorpion EVO models (except 3+)
NOT COMPATIBLE: CZ Scorpion EVO 3+

WARNING: DO NOT OVERTIGHTEN set screw when installing. Tighten only until end of set screw is flush with the nut. Failure to properly install will result in magazine not dropping freely.

Converts AK rear sight into a 1913 Picatinny rail for mounting low-profile optics onto your AK rifle.

Note: Highly recommend to use "Red Loctite" on screws.

The Strike Pistol Grip Plug Tool Holder Insert is a drop-in installation insert with compatible SI pistol grip plugs. Directly install this tool holder insert into your the grip plug that is included with your SI pistol grip and give yourself an instant added organized storage compartment. Securely store multiple punch, hex, torx, firing pin reservoir and other similar tools. The small reservoir is included with this Strike Pistol Grip Tool Holder Insert that safely stores backup oil, grease, threadlocker and similar materials. The designed divider slots help prevent the tools from rattling around in the SI pistol grip cavity. If your weapon uses an optic with the common CR2032 battery (not waterproof), keep a backup in this tool holder along with other tool(s). The Strike Pistol Grip Plug Tool Holder Insert gives you a speedy tool-less installation and removable grip plug when sh*t happens or a convenient way to make adjustments to your equipment.

COMPATIBILITY:
-SI Enhanced Pistol Grip
-SI AR Multi-Angle Pistol Grip
-AR Flat Top Overmolded Pistol Grip (15-Degree)
-SI AK Enhanced Pistol Grip
-SI Pistol Grip for CZ Scorpion EVO
NOT COMPATIBLE:
-SI AR Overmolded Pistol Grip
-SI Simple Featureless AR Grip
-SI Megafin Featureless AR Grip
-SI AK Simple Featureless Grip

Keep the look of your existing stock and buffer tube but be able to convert it to fixed! The Stock Stop is the most affordable, easiest, and quickest way to convert your collapsible stock into a fixed stock. The Stock Stop fills in all but one receiver extension hole. This ensures that the stock cannot be adjusted to another position.  Compatible with any aftermarket 6-position buffer tube or our 7-position Advanced Receiver Extensions, the Stock Stop requires no modification to the buffer tube-- simply cut the piece to fit, and it drops right in. No need to drill and pin your existing stock. Made out of high strength and abrasion resistant TPU, the stop is ensured to stay in place, and out of sight.

COMPATIBILITY: Mil-Spec 6 position stocks with the positions evenly spaced apart.

DISCLAIMER: This device is made to conform to the DOJ criteria but has not been approved.  If the Stock Block is used in conjunction with other features on the CA DOJ banned features list, the host system no longer constitutes a “featureless” build.  Please consult your local laws and regulations to ensure compliance.